How to enable DHT11/22 sensor in AirSniffer

[esky-sh]

logServer.py line 24；

Code: Select all

defPMParameter = {'SensorName':'PMS5003ST' , 'Uart#':4 , 'ResetPin#':'GPIO2_IO00' , 'SetPin#':'GPIO2_IO01'}
defHCHOParameter = {'SensorName':'PMS5003ST' , 'Uart#':4 , 'ResetPin#':'GPIO2_IO00' , 'SetPin#':'GPIO2_IO01'}
defTEMPParameter = {'SensorName':'PMS5003ST' , 'Uart#':4 , 'ResetPin#':'GPIO2_IO00' , 'SetPin#':'GPIO2_IO01'}
defHUMIParameter = {'SensorName':'PMS5003ST' , 'Uart#':4 , 'ResetPin#':'GPIO2_IO00' , 'SetPin#':'GPIO2_IO01'}
defCO2Parameter = {'SensorName':'S8_0053' , 'Uart#':2 }
defDBParameter = {'Interval':1}

change to:

Code: Select all

defPMParameter = {'SensorName':'PMS5003ST' , 'Uart#':4 , 'ResetPin#':'GPIO2_IO00' , 'SetPin#':'GPIO2_IO01'}
defTEMPParameter = {'SensorName':'DHT22' , 'DataPin#':'GPIOX_XXXX'}
defHUMIParameter = {'SensorName':'DHT22' , 'DataPin#':'GPIOX_XXXX'}
defCO2Parameter = {'SensorName':'S8_0053' , 'Uart#':2 }
defDBParameter = {'Interval':1}

Where GPIOX_XXXX stand for GPIO pin can be chosen from following list:

Code: Select all

pinMap = {'GPIO1_IO00':0, 'GPIO1_IO01':1, 'GPIO1_IO02':2, 'GPIO1_IO03':3, 'GPIO1_IO04':4, 'GPIO1_IO05':5, 'GPIO1_IO06':6, 'GPIO1_IO07':7, \
    'GPIO1_IO08':8, 'GPIO1_IO09':9, 'GPIO1_IO10':10, 'GPIO1_IO11':11, 'GPIO1_IO12':12, 'GPIO1_IO13':13, 'GPIO1_IO14':14, 'GPIO1_IO15':15, \
    'GPIO1_IO16':16, 'GPIO1_IO17':17, 'GPIO1_IO18':18, 'GPIO1_IO19':19, 'GPIO1_IO20':20, 'GPIO1_IO21':21, 'GPIO1_IO22':22, 'GPIO1_IO23':23, \
    'GPIO1_IO24':24, 'GPIO1_IO25':25, 'GPIO1_IO26':26, 'GPIO1_IO27':27, 'GPIO1_IO28':28, 'GPIO1_IO29':29, \
    'GPIO2_IO00':32, 'GPIO2_IO01':33, 'GPIO2_IO02':34, 'GPIO2_IO03':35, 'GPIO2_IO04':36, 'GPIO2_IO05':37, 'GPIO2_IO06':38, 'GPIO2_IO07':39, \
    'GPIO2_IO08':40, 'GPIO2_IO09':41, 'GPIO2_IO10':42, 'GPIO2_IO11':43, 'GPIO2_IO12':44, 'GPIO2_IO13':45, 'GPIO2_IO14':46, 'GPIO2_IO15':47, \
    'GPIO4_IO11':107, 'GPIO4_IO12':108, 'GPIO4_IO13':109, 'GPIO4_IO14':110, 'GPIO4_IO15':111, 'GPIO4_IO16':112 }